Extending the response spectrum of organic photodetectors by quaternary active layer method with complementary absorption spectra

In this work, we report a new method for extending the response spectra of organic photodetectors (OPDs) by incorporating PBDT-TT-C and PBDT-TT-F in the P3HT:PC₆₁BM. The effects of PBDT-TT-C and PBDT-TT-F incorporation on the optical and electrical properties of OPDs were investigated, It was found that when the mass ratio of P3HT:PBDT-TT-F:PBDT-TT-C:PC₆₁BM was 12:2:2:8, the response spectrum of the active layer was extended to 780 nm. The responsivity (R) and external quantum efficiency (EQE) of the OPDs reached 340, 376, 315 mA/W and 67%, 88%, 85% under 630, 530, and 460 nm illumination and −1 V bias, respectively, and the detectivity (D*) reached 10¹² Jones. The results show that the inclusion of an appropriate amount of donor material with similar chemical structure and complementary absorption spectrum can reduce the influence of the doping material on the micro-morphology of the original film while improving the absorption of the spectrum. The interaction between the donor materials promotes the generation of photogenerated carriers and increases the photocurrent of the OPDs. In addition, the incorporation of the different component promotes crystallization of the film, resulting in a reduction in dark current of the OPDs.     

Switching of heating and cooling modes using thermal radiation films

We study emissivity (ε)-dependent radiative heat transfer phenomena in remote and contact configurations. To demonstrate the emissivity-dependent radiative heating mode in a remote configuration, we fabricated miniature greenhouses covered with low (0.34)- and high-ε (0.86) polyethylene films and monitored temperatures on the floors, insides, and covers of the greenhouses during 24 h. The high-ε greenhouse yielded a 9-°C increase in floor temperature relative to the low-ε greenhouse at a one-sun solar irradiance because the high-ε film effectively trapped floor radiation. In contrast, the cover temperature remained lower in the high-ε greenhouse due to intensified radiation released from the high-ε film. This self-cooling effect was more evident when an emissive film was in physical contact with an object. While bare copper heated up to 55 °C, a high-ε film coated copper substrate was kept cooler by 4 and 2 °C compared with the bare and low-ε film coated copper samples, respectively.     

Synthesis,Electrochemistry, and Photophysics of Aza‐BODIPY Porphyrin Dyes

The synthesis of dyad and triad aza‐BODIPY‐porphyrin systems in two steps starting from an aryl‐substituted aza‐BODIPY chromophore is described. The properties of the resulting aza‐BODIPY‐porphyrin conjugates have been extensively investigated by means of electrochemistry, spectroelectrochemistry, and absorption/emission spectroscopy. Fluorescence measurements have revealed a dramatic loss of luminescence intensity, mainly due to competitive energy transfer and photoinduced electron transfer involving charge separation followed by recombination.     

Synthesis of poly(n‐butyl acrylate) homopolymer and poly(styrene‐b‐n‐butyl acrylate‐b‐styrene) triblock copolymer via AGET emulsion ATRP using a cationic surfactant

Cationic emulsions of triblock copolymer particles comprising a poly(n‐butyl acrylate) (PⁿBA) central block and polystyrene (PS) outer blocks were synthesized by activator generated by electron transfer (AGET) atom transfer radical polymerization (ATRP). Difunctional ATRP initiator, ethylene bis(2‐bromoisobutyrate) (EBBiB), was used as initiator to synthesize the ABA type poly(styrene‐b‐n‐butyl acrylate‐b‐styrene) (PS‐PⁿBA‐PS) triblock copolymer. The effects of ligand and cationic surfactant on polymerizations were also discussed. Gel permeation chromatography (GPC) was used to characterize the molecular weight (M_n) and molecular weight distribution (MWD) of the resultant triblock copolymers. Particle size and particle size distribution of resulted latexes were characterized by dynamic light scattering (DLS). The resultant latexes showed good colloidal stability with average particle size around 100–300 nm in diameter. Glass transition temperature (T_g) of copolymers was studied by differential scanning calorimetry (DSC). © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 611–620     

Role of the Bridge in Photoinduced Electron Transfer in Porphyrin–Fullerene Dyads

The role of π‐conjugated molecular bridges in through‐space and through‐bond electron transfer is studied by comparing two porphyrin–fullerene donor–acceptor (D–A) dyads. One dyad, ZnP–Ph–C₆₀ (ZnP=zinc porphyrin), incorporates a phenyl bridge between D and A and behaves very similarly to analogous dyads studied previously. The second dyad, ZnP–EDOTV–C₆₀, introduces an additional 3,4‐ethylenedioxythienylvinylene (EDOTV) unit into the conjugated bridge, which increases the distance between D and A, but, at the same time, provides increased electronic communication between them. Two essential outcomes that result from the introduction of the EDOTV unit in the bridge are as follows: 1) faster charge recombination, which indicates enhanced electronic coupling between the charge‐separated and ground electronic states; and 2) the disappearance of the intramolecular exciplex, which mediates photoinduced charge separation in the ZnP–Ph–C₆₀ dyad. The latter can be interpreted as a gradual decrease in electronic coupling between locally excited singlet states of D and A when introducing the EDOTV unit into the D–A bridge.     

A new Monte Carlo model for predicting the mechanical properties of fiber yarns

Understanding the complicated failure mechanisms of hierarchical composites such as fiber yarns is essential for advanced materials design. In this study, we developed a new Monte Carlo model for predicting the mechanical properties of fiber yarns that includes statistical variation in fiber strength. Furthermore, a statistical shear load transfer law based on the shear lag analysis was derived and implemented to simulate the interactions between adjacent fibers and provide a more accurate tensile stress distribution along the overlap distance. Simulations on two types of yarns, made from different raw materials and based on distinct processing approaches, predict yarn strength values that compare favorably with experimental measurements. Furthermore, the model identified very distinct dominant failure mechanisms for the two materials, providing important insights into design features that can improve yarn strength.     

Synthesis and liquid crystalline behavior of bulky poly(methacrylamide)s

N‐(Bis(4‐(2‐ethylhexyloxy)phenyl)(phenyl)‐methyl)methacrylamide was synthesized and polymerized via reversible addition‐fragmentation chain‐transfer (RAFT) polymerization. The chain‐transfer agent (4‐cyano‐4‐(phenylcarbonothioylthio) pentanoic acid (CPADB)), combined with a chiral additive, and a radical initiator yielded polymers with dispersities between 1.2 and 1.4. At low concentrations, the polymers are soluble in hexanes and chloroform while at higher concentrations they swell in these solvents. Characterization of the polymers by wide‐angle X‐ray scattering (WAXS) revealed an interplanar distance of 19.0 Å. The WAXS data combined with polarized optical microscopy support a lamellar crystallization and lyotropic liquid crystalline behavior in hexanes and chloroform. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 2563–2568     

Synthesis of tertiary amine‐based pH‐responsive polymers by RAFT Polymerization

Well‐defined tertiary amine‐based pH‐responsive homopolymers and block copolymers were synthesized via reversible addition‐fragmentation chain transfer (RAFT) polymerization using 4‐cyanopentanoic acid dithiobenzoate (CPAD) as the RAFT agent for homopolymers and a poly(ethylene glycol) (PEG) macro‐RAFT agent for the block copolymers. ¹H NMR and gel permeation chromatography results confirmed the successful synthesis of these homopolymers and block copolymers. Kinetics studies indicated that the formation of both the homopolymers and the block copolymers were well defined. The pKa titration experiments suggested that the homopolymers and the related block copolymers have a similar pKa. The dynamic light scattering investigation showed that all of the block copolymers underwent a sharp transition from unimers to micelles around their pKa and the hydrodynamic diameter (D_h) was not only dependent on the molecular weight but also on the composition of the block copolymers. The polymer solution of PEG‐b‐PPPDEMA formed the largest micelle compare to the PEG‐b‐PDPAEMA and PEG‐b‐PDBAEMA with a similar molecular weight. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 1010–1022     

Butylated hydroxytoluene enediyne: access to diradical and electrophilic quinone methide intermediates

A theoretical study was carried out on the unimolecular reaction of an enediyne with a fused butylated hydroxytoluene to internally scavenge the p‐benzyne diradical sites formed after the Bergman cyclization. The calculations revealed that the conversion of the p‐benzyne diradical (2‐tert‐butyl‐4‐methyl‐5,8‐didehydro‐1‐naphthalenol) to p‐quinone methide is favored over the conversion to a phenoxy/benzene diradical 4 in an approximate 95:5 ratio. Based on this model, the Bergman cyclization leads in a bifunctional manner to intermediates for competing reactivity with intermolecular H‐atom abstraction. Copyright © 2015 John Wiley & Sons, Ltd.